Can You Replace Battery on Iphone 6s Plus

Introduction

Apply this guide to bring life back to your iPhone 6s Plus with a new battery. If your battery is swollen, have appropriate precautions.

This guide instructs you to disassemble the front panel assembly; this is intended to prevent damage to the brandish cables. If yous feel comfortable supporting the display carefully while peeling the battery out of the iPhone, you can skip the display removal and go directly to the battery removal steps.

For optimal functioning, afterwards completing this guide, calibrate your newly installed battery: Charge it to 100% and proceed charging it for at least two more hours. Then use your iPhone until it shuts off due to low battery. Finally, charge information technology uninterrupted to 100%.

Y'all can besides utilize this guide to replace the bombardment connector bracket.

Video Overview

• Before disassembling your iPhone, belch the bombardment below 25%. A charged lithium-ion battery tin can catch fire and/or explode if accidentally punctured.

• Power off your iPhone before beginning disassembly.

• Remove the two three.4 mm Pentalobe screws on either side of the Lightning port.



• Optionally, utilise mild rut to the lower edge of the iPhone using an iOpener or pilus dryer for most a minute.

• Heat softens the adhesive securing the display, making it easier to open.

• Opening the display on the 6s Plus separates a sparse strip of adhesive around the perimeter of the display. If y'all prefer to supplant the adhesive, have a fix of new agglutinative strips ready earlier yous continue. Information technology'south possible to complete the repair without replacing the adhesive, and you lot probably won't notice whatsoever difference in functionality.

• Utilise a suction cup to the lower left corner of the brandish assembly.

• If your brandish is desperately cracked, covering information technology with a layer of clear packing tape may allow the suction loving cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you tin can superglue the suction loving cup to the broken screen.

• Pull upward on the suction cup with firm, abiding pressure to create a slight gap between the front console and rear case.

• Pulling likewise hard may harm the display assembly. Apply only enough pressure level to create a small gap between the display assembly and the rear instance.

• The safest place to pry from is the notch in the front console above the headphone jack.

• While still maintaining pressure on the suction loving cup, insert the flat tip of a spudger into the gap, directly above the headphone jack.

• Twist the spudger to widen the gap between the front console and the rear case.

• While firmly pulling upwardly on the suction cup, slide the edge of the spudger under the bottom left corner of the display.

• Slide the tip of the spudger upward the left side of the phone, between the front console and the rear case.

• Insert the flat tip of the spudger under the correct edge of the display.

• Slide the spudger up the right side.

• Employ a plastic opening tool to hold downward the rear case while pulling up the suction cup to open the phone.

• Practise non remove the display completely, or you will damage the data cables connecting the display nigh the top edge of the iPhone.

• Pull upward on the pocket-sized nub on the suction cup to remove information technology from the display.

• Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.

• Open up the display to well-nigh a 90º angle, and lean it against something to keep it propped up while you're working on the phone.

• Don't open the brandish more 90º—it is withal connected to the top of the telephone past the display, digitizer, and forepart camera cables which tin can tear easily.

• Add together a rubber band to go on the display securely in place while y'all work. This prevents undue strain on the display cables.

• In a pinch, you can utilise an unopened canned beverage to back up the brandish.

• Remove two Phillips screws securing the battery connector bracket to the logic board, of the following lengths:

• I 2.ix mm screw

• One 2.3 mm screw

• Throughout this guide, go on careful rail of your screws so that each one goes back where it came from during reassembly. Installing a screw in the incorrect identify can cause permanent damage.

• Remove the battery connector bracket.

• Utilize a spudger or a clean fingernail to disconnect the battery connector by prying it direct upwards off the logic board.

• Bend the connector dorsum to ensure it doesn't make contact and power the iPhone on while you're working on information technology.

• Remove the following Phillips screws:

• Three 1.three mm screws

• One i.half-dozen mm spiral

• One 3.0 mm screw

• During reassembly, it'south critical to place this 3.0 mm screw in the top-correct corner of the bracket. Placing information technology anywhere else may impairment the logic lath.

• Remove the display cable bracket.

• Be careful to only pry upwardly on the connector itself and not the socket on the logic board.

• Use a plastic opening tool to disconnect the front-facing photographic camera and sensor cable connector.

• Use a plastic opening tool to disconnect the digitizer cable past prying it straight up from its socket on the logic board.

• When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, and so press the opposite end. Pressing in the center of the connector can bend the component and crusade digitizer damage.

• Make certain the battery is asunder before you disconnect or reconnect the cable in this step.

• Disconnect the dwelling button/fingerprint sensor cablevision past prying information technology straight up from its socket on the logic board.

• Remove the display assembly.

• During reassembly, intermission here if you wish to supervene upon the agglutinative effectually the edges of the brandish.

• Pare back the tips of the three battery adhesive strips along the lesser edge of the battery.

• Gather the ends of all 3 adhesive strips in your hand.

• Try to keep the strips apartment and unwrinkled during this procedure; wrinkled strips volition stick together and intermission instead of pulling out cleanly.

• If any of the agglutinative strips broke off underneath the bombardment and could not be retrieved, apply a few drops of high concentration (over 90%) isopropyl alcohol nether the edge of the battery in the area of the broken adhesive strip(s).

• Look about one minute for the booze solution to weaken the adhesive. Use the flat end of a spudger to gently lift the battery.

• Don't try to forcefully lever the battery out. If needed, utilize a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

• Do not insert the spudger in the area betwixt the volume downwardly (-) push and the top edge of the bombardment, or you may damage the book control cable lying underneath. Do not pry against the logic board or you may impairment the phone.

• Gently pull the battery adhesive tabs abroad from the battery, toward the bottom of the iPhone.

• To avoid vehement the adhesive strip, be careful not to pull against the battery or lower components.

• Pull steadily, maintaining abiding tension on the strips every bit they slip out from betwixt the bombardment and the rear case. For best results, pull the strips at a 60º angle or less.

• The strips volition stretch to many times their original length. Continue pulling and re-take hold of the strips nigh the battery if necessary.

• Hold down the battery with ane hand as you pull, or the elastic strips may fling the battery from the telephone once they're separated from the rear case.

• If the adhesive breaks off underneath the bombardment and tin't exist retrieved, refer to the previous step for instructions on how to unstick the battery. See the side by side pace for boosted methods.

• If you lot successfully removed all three adhesive strips, move on to the next step. Otherwise, you will need to pry the battery from the rear example.

• Set an iOpener and use information technology to the back of the rear case, straight over the battery. Otherwise, you lot tin can apply oestrus using a heat gun or pilus dryer.

• Overheating the iPhone may ignite the battery.

• Don't try to forcefully lever the bombardment out. If needed, utilize a few more drops of booze to further weaken the adhesive. Never deform or puncture the bombardment with your pry tool.

• Do not insert the spudger in the area between the volume down (-) button and the top edge of the battery, or you may harm the volume control cable lying underneath. Do non pry against the logic board or you may damage the phone.

• Alternatively, a slice of dental floss may be used to separate the battery from the rear case. A stronger alternative to dental floss is an unwound guitar string, such as a 0.009 E cord from a 12-string set.

• Thread the floss or string behind the upper bombardment corners, bring the ends together, wrap them around a folded cloth, and pull evenly.

• Remove the battery.

• If your replacement battery came in a plastic sleeve, remove the sleeve before installation by pulling information technology abroad from the the ribbon cable.

• If in that location's whatever alcohol solution remaining in the phone, advisedly wipe it off or allow it to air dry before installing your new battery.

• Earlier you adhere the replacement bombardment, temporarily reconnect the battery connector to the logic lath socket. This ensures that the battery is properly aligned in its recess.

• Attach the bombardment, disconnect information technology, and continue reassembling your device.

• If your new battery doesn't have agglutinative preinstalled, refer to this guide to supercede the adhesive strips.

• Perform a hard reset after reassembly. This can forbid several bug and simplify troubleshooting.

Conclusion

Compare your new replacement office to the original role—you may need to transfer remaining components or remove adhesive backings from the new part earlier installing.

To reassemble your device, follow the above steps in reverse social club.

Take your eastward-waste to an R2 or e-Stewards certified recycler.

Repair didn't get as planned? Check out our Answers customs for troubleshooting assist.

Team

Embed this guide

Choose a size and copy the lawmaking beneath to embed this guide as a small widget on your site / forum.

Preview

everettthoon1985.blogspot.com

Source: https://www.ifixit.com/Guide/iPhone+6s+Plus+Battery+Replacement/51380

Share this post